Interested in linking to "On the fly "?
You may use the Headline, Deck, Byline and URL of this article on your Web site. To link to this article, select and copy the HTML code below and paste it on your own Web site.
The gold standard for pest control in food and beverage plants is Integrated Pest Management (IPM), an ongoing, preventive control system that reduces pesticide use through sanitation, exclusion and other techniques. IPM employs the use of several control measures: inspection, exclusion, sanitation and, when necessary, minimal use of pesticides. Pesticides are the treatment of last resort and only should be used to target particular pest species at particular locations within the plant.
Whenever pest activity is noted, devices such as glue boards, insect light traps, and multi-catch traps should form the first line of defense. Next, check for entry points that need attention. Look for breaks in caulk, sealants, screens, weather stripping and cement mortar.
Proper sanitation is critical. To avoid attracting pests, keep all food and beverage waste in closed containers. Remove waste several times each day to the proper outdoor trash receptacle. Clean the inside of waste containers daily and use trash can liners, and routinely remove trash and debris from around the building.
Flies are a major problem in even the cleanest processing plant, since they thrive in warm, moist conditions with a ready food supply. Dual doors and air curtains can be installed to prevent flies from entering. Light also plays an important role in fly control, with exterior lighting being a primary consideration. Change direct lighting on the building to indirect lighting, away from the structure. Install high-intensity ultraviolet lights farther away from the building to draw insects away. Closer to the facility, install mercury vapor lights so they shine toward guest and employee entrances. If it is necessary to install lights on the building, sodium vapor lighting is more effective than mercury vapor in minimizing fly attraction.
While many processing plants are skeptical about spending money to replace lighting, the investment pays off handsomely in terms of overall pest management expenditures.
Along with proper sanitation, insect light traps (ILTs) can also reduce dependence on chemical control methods. However, ILTs are only a small part of the overall fly control program. In fact, these devices should be considered "flying insect monitors" rather than control devices. They do remove adult flies from circulation, but should not be the only control method. Again, sanitation is the key to reducing fly populations.
While the fly light is sometimes viewed as nothing more than a box with glue and light bulbs in it, design does have an impact on the unit's efficacy. Units that have too much closure on the front grill may provide less light output, thereby attracting fewer flies. Units with too much open space in front may catch clothes, fingers, cigarette butts -- even trash.
Which ILT should you choose for your facility? The answer is based on several factors. The most important units are for kitchen or food processing areas. A second type is a large industrial device for large production facilities and warehouses. The third type, also known as a sconce or decorative unit, is for any public area. The fourth, an electrocution device, can be used outdoors or in non-food warehousing areas. Not all electrocution devices are certified for outdoor use, so review manufacturer specifications prior to installation.
As in real estate, location is the critical factor with ILTs. Placement should be based on several factors. Competing light sources must be considered. An ILT placed in direct sunlight is not going to catch many flies. Similarly, an ILT won't be successful if it is placed where security lights compete with it. If the flies can't distinguish the ILT's ultraviolet (UV) output from other lighting, artificial or otherwise, they may not enter the traps.
The ideal place to locate an ILT is where insects are congregating. A very thorough inspection can determine the best location. Look for signs of fly rest areas, including the presence of "specs," which are fecal material. Place the ILT as close to these areas as possible. Keep in mind that there are often several such locations in a given facility. The resting areas may change throughout the day as temperature and light patterns shift.
Further, different fly species are attracted to lights located at different heights. Daytime flying insects, such as the housefly, are caught in the so-called "strike zone", the space from the knees to the shoulders. This range, three to six feet, is where ILTs should be placed, if day flyers are the only target. For nighttime flying insects, such as moths, ILTs should be wall- mounted eight to ten feet off the floor.
Depending on the facility, you most likely will have several species of flying insects. Be creative. You may need ILTs that are on in the daytime, and a separate set that is on at night, or at varying times of day. Your pest control technician should do a complete site survey prior to recommending and installing units.
The areas under the mounted units must also be considered. Although ILTs have a glue board in them to catch and hold insects, they should never be installed over food contact surfaces, such as prep tables, prep/wash sinks or processing conveyor lines. If service is missed and the glue on the board starts to dry, the insects may fall out of the units. Not all insects that die in an ILT are caught on the glue board. If the airflow in the facility is moving across the front of the unit, it can blow out loose insects.
Again, insect light traps should be considered a monitoring device. Analyzing the contents of the traps should provide clues about the possible source of an infestation. Knowing some basic biology of common flying insects in your region will likewise help pinpoint the source. Keep a record of the catch and analyze the trend. If an increase in a given species occurs at the same time each month or year, take a proactive approach.
Not all pests that fly can be called flies. Many stored-product insects can attack raw goods as well as finished product. Treatments for these types of insects have changed greatly.
With the phase-out of methyl bromide looming, food processors are looking to less conventional pest management techniques, such as heat. Heat treatments are sometimes employed by organic food processors, and by large food processing and grain storage companies, as part of their IPM programs.
As an alternative to conventional fumigation methods, heat offers a number of advantages:
- It delivers a 100 percent kill ratio because it eliminates all stages of insect life.
- Heat requires minimized preparation of the area to be treated.
- Spot treatments can be performed, making it unnecessary to shut down or evacuate an entire facility, thereby reducing plant downtime and production losses.
Heat treatment works by raising room temperature to 126 to 131 degrees F in increments of five to 10 degrees per hour. This process may take as little as eight or as many as 30 hours. During heat treatment, insects are killed by dehydration, and the destruction of some of their key enzymes and proteins. Some food processing and storage facilities are ideal candidates for heat treatment because the products and equipment are able to withstand the high temperature levels. Warehouses used for imported commodities that require fumigation also are good candidates.
IPM considers a multitude of situations and solutions for pest control. Since each environment is unique, sanitation and quality control managers should work with their pest control provider to design customized solutions.
As new research and federal regulations continue to limit pesticide use in food processing, pest control companies are continually developing effective new products and treatments. Food processors can potentially improve their corporate image and enhance employee safety by choosing environmentally friendly solutions.
Insect light traps: do's and don'ts
FoodProcessing.com is the go-to information source for the food and beverage industry. We offer processing best practices as well as new products, equipment and ingredients for food and beverage processors.